dvgt is a version of the DVItoVDU interactive TeX page previewer. The program allows you to look at TeX-generated DVI files on a variety of commonly available VDUs. The "DVItoVDU User Guide", "userguide.tex", explains how to use the program. USAGE: dvgt filename[.dvi] [-H x_offset] [-V y_offset] [-d dummy_pk] [-e dummy_tfm] [-f pk_directory] [-h helpfile] [-i] [-l] [-m magnification] [-p postscript_font_prefix] [-r xres yres] [-t tfm_directory] [-v vdu] [-x paperwd] [-y paperht] NOTE ON OPTIONS' DEFAULTS: All options have default values. System dependent initial defaults are set at compile-time. (Compilation note: these constants are set in the source file "defaults.h".) Some defaults can be set by environment variables. The command line options override the environment variables, which in turn override the compiled initial defaults. BRIEF SUMMARY OF OPTIONS: -H horizontal_offset (default = 0.0 in) -V vertical_offset (default = 0.0 in) -l (set landscape mode, instead of the default portrait mode) -m magnification (default = DVI file's intrinsic magnification) -v vdu (default = value of the environment variable TERM) vdu may be one of: aed512 gigi kermit ncsatel regis tek4010 vis240 vis241 vis500 vis550 vis603 vis630 vk100 vt100 vt100132 vt102 vt125 vt200 vt220 vt240 vt640 The other options' default values are system dependent. Try "dvgt -f", for example, to find the current default PK font directory. COMMAND OPTIONS: -H horizontal_offset (default = 0.0in) -V vertical_offset (default = 0.0in) TeX, by default, considers the top left corner of the printed page as one inch below and one inch to the right of the physical page. So does dvgt. The two offsets move this corner. Positive dimensions move it downwards and rightwards; negative offsets are allowed. -d file (default is system dependent; environment: DV_DUMMY_PK) dvgt will warn you if your document uses a font at a non-existent size. Rather than abort, it will load the PK font specified after -d and continue so you can look for more errors. Paragraphs using this dummy information are likely to have ragged right margins. -e file (default is system dependent; environment: DV_DUMMY_TFM) Default TFM file, similar to -d option. -f file (default is system dependent; environment: PKFONTS or TEXFONTS) dvgt gets all its font information from PK files. These files are kept within the directory specified by this option. -h file (default is system dependent; environment: DV_HELP) The ? command reads the help text file specified by this option. -i (default is system dependent; environment: DV_IMMED_HELP) Display the path name of the immediate help file. Typing "dv" by itself displays the immediate help file. -l Set landscape mode: exchange x and y dimensions. (This does NOT rotate the page, sorry.) The default is portrait mode. -m i (default = DVI magnification) This option allows you to replace the magnification used in the DVI file with some other value; i is a positive *integer*, 1000 times the desired magnification. The given value should be chosen carefully so that the new font sizes still correspond to existing PK files. Unless you know exactly what you are doing you should avoid using -m, especially if your TeX source file uses \magnification AND true dimensions. -r x,y (default is system dependent) -r x dvgt treats the imaginary sheet of paper on which a DVI page will appear as a two dimensional array of tiny dots known as paper pixels. x and y are positive floating point numbers that define the numbers of pixels per inch in the horizonatl and vertical directions, respectively. Their values should match the respective resolutions of the device that will be used to print your document. If only one value is given, then it is used as the resolution both horizontally and vertically. -t tfm_directory (default is system dependent; environment: TEXFONTS) This sets the directory where dvgt will look for TFM (TeX Font Metric) files, such as "cmr10.tfm". -v string (default = value of TERM) This option is used to tell dvgt what type of VDU you are using. If TERM does not describe your VDU, you need to override the default value. Typing `dvgt -v vis550 foo' will tell dvgt you're using a VISUAL 550. The current version will accept the following strings (in upper or lower case): aed512 (AED 512 with 512 by 512 screen) kermit (same as ncsatel) ncsatel (NCSA Telnet's Tektronix 4010 emulation) regis (any ReGIS compatible VDU; synonyms = GIGI, VK100, VT125, VT240) tek4010 (same as ncsatel) vis240 (VISUAL 240; synonym = VIS241) vis500 (VISUAL 500) vis550 (VISUAL 550) vis603 (VISUAL 603) vis630 (VISUAL 630) vt100 (any VT100 compatible VDU in 80 column mode; synonym = VT102) vt100132 (any VT100 compatible VDU in 132 column mode) vt220 (VT220 using down-loaded chunky graphics; synonym = VT200) vt640 (VT100 with Retro-Graphics) -x dimen (default is system dependent) -y dimen (default is system dependent) These two options define the width and height of the paper upon which your document will be printed. Both values are specified as dimensions like those used in TeX, but the units are restricted to BP, CM, IN, MM, PC, PT, PX, or SP. PX is specific to dvgt, and represents one paper pixel. Every time you select a page, dvgt will use these paper dimensions to check that all printed material falls within the paper edges.